# Shower Head Spare Parts and Consumables: A Reference List

Source: https://www.ningboware.com/resources/shower-head-spare-parts-and-consumables/
Publisher: Cixi Zhonghe Sanitary Appliance Factory (ZHONGHE), Cixi, Ningbo, Zhejiang, China. Contact: steven@ningboware.com
Updated: 2026-09-03

> A shower head has two spare part populations. Sealing and connection parts fail rarely and cost almost nothing: O-rings, the hose washer, the filter washer, the cone nut. Media cartridges are consumables that are meant to be replaced. ZHONGHE supplies replacement cartridges as separate SKUs, and a distributor should order both populations against a written service policy.

## Key facts

| Item | Detail |
| --- | --- |
| Two populations | Failure parts such as seals, washers and nuts, and consumables such as media cartridges and restrictors |
| O-rings | 100% inspected at the supplier with high precision industrial cameras and AI image inspection; sizes are model specific |
| Hose washer | The flat rubber washer inside the 1/2 inch hex nut; material, hardness and thickness decide how much torque produces a seal |
| Filter washer | A washer carrying a mesh screen that catches grit at the supply end; supplied with hoses on request |
| Check valve | Fitted at the hose supply end where a market's backflow rules or a buyer's specification require it, rather than as standard |
| Flow restrictor | The insert that sets flow at a given pressure; removing it invalidates the tested figure and can take a product outside a market limit |
| Cartridge media | ACF, PP cotton, calcium sulfite, mineral or metasilicate beads and vitamin C; refill cartridges are supplied as separate SKUs |
| Service life evidence | Media are consumables; ACF testing showed over 96.8% initial free chlorine removal and 90.6% after 5 tons of continuous flow |

## Which Parts Actually Fail

Spare part planning goes wrong when a distributor treats every component as equally likely to need replacing. In practice a shower head has a few parts that fail, a few more that get lost or damaged during installation, and a set of media designed from the outset to be used up.

The parts that fail are almost always sealing parts, and they usually fail because of how they were fitted rather than what they are made of. An O-ring pinched during assembly, a washer crushed by an overtightened wrench, a cone nut cross threaded by a customer: none is a manufacturing defect, and all present to the retailer as a leak. The cheapest part in the product is the one worth stocking most deeply.

Media are a different business. A filter cartridge is not a spare part, it is a repeat purchase, and a filter head sold without a refill supply is a one year product. Forecast cartridges as a sales line, and set the replacement interval before the packaging is printed.

## Sealing and Connection Parts

The table below is written to be turned into part numbers. Each row is a real line item that can appear on a purchase order, with the information the factory needs in order to ship the right thing, and the failure mode that tells you how deeply to stock it.

| Part | What it does | How to specify it | What goes wrong |
| --- | --- | --- | --- |
| O-ring | Seals internal joints between head, handle and the mode switching structure | Model and position, material such as NBR or silicone, and the size list from the factory | Pinched or cut during assembly, or hardened after long exposure to hot water |
| Hose washer, 1/2 inch | Seals the hex nut against the mixer outlet | 1/2 inch flat washer, with material and thickness stated rather than assumed | Overtightening deforms it, and a hardened washer weeps slowly rather than failing outright |
| Filter washer | A washer with a mesh screen that catches grit before it reaches the head | State whether it ships installed in the nut or bagged alongside the hose | Blocks over time on sediment heavy supply, which the customer reports as low pressure |
| Cone nut | The conical nut at the head end of the hose; seats into the inlet and lets the head swivel | G1/2, with the finish matched to the head | Cross threading during first installation, almost always by the end user |
| Hex or flat nut | The supply end nut at the mixer | G1/2, specified together with its washer | Plated finish marked where a wrench was used without a cloth |
| Check valve | Prevents backflow into the supply where a rule or specification requires it | Name the market rule or specification that requires it; it is not standard on every hose | Adds pressure loss, which is noticeable on a weak supply |
| Adapter, S, G, K or M | Converts the G1/2 head side to a legacy fitting | S = M22.1 x 1.5, G = M21.3 x 1.5, K = M21.5 x 2, M = M22.1 x 1.75 | The wrong one in the box, because the country was used to choose it instead of the actual fitting |

## Consumables and Service Life

Service life for filter media is driven by throughput rather than by the calendar. A cartridge in a two person household and the same cartridge in a family of five reach the same depletion at very different dates, which is why an interval printed as a number of months is a marketing simplification of a number of litres. State both if you can: the throughput the data supports, and the months that throughput represents for typical use in your market.

The evidence column below is deliberately precise about what was tested. These are component level results on the media, produced under stated laboratory conditions, and not performance guarantees for a finished shower head across a cartridge life. Quoting them any other way turns a defensible fact into an indefensible claim.

| Consumable | Function | Evidence that exists | Service life logic |
| --- | --- | --- | --- |
| Activated carbon fiber (ACF) cartridge | Free chlorine reduction | 99.5% removal at start of flow in SGS testing to GB/T 5750.11-2023; separately over 96.8% initial and 90.6% after 5 tons of continuous flow | Throughput drives depletion, so state an interval in litres or tons and translate it into months for the market's usage |
| Calcium sulfite media | Chlorine reduction that works in hot and cold water | Drinking water grade hygiene testing across 16 assessed items, with RoHS non detect | High hardness and hot water tolerance make it the durable partner to ACF in a blended cartridge |
| PP cotton | Sediment and particle capture | Qualitative function, with no percentage claimed | Depletes fastest on sediment heavy supply, and protects the media behind it while it does |
| Mineral or metasilicate beads | Conditions water toward mildly alkaline | Test reference pH 8.1, with REACH SVHC screening | Lifestyle positioning only; visible colour change is not a reliable depletion indicator |
| Vitamin C cartridge | Dechlorination through the media | Buyers who need a specific test report for their market should state it in the RFQ | Depletes visibly as the gel or granules are consumed, which is part of its retail appeal |
| Flow restrictor | Sets the flow rate at a given pressure | Bench verified at 0.3MPa for selected specifications | Not a wear part but a service part, because customers remove them and then ask for replacements |
| Nozzle plate or face plate | Produces the spray pattern | Silicone nozzle cones let scale be wiped out of the holes by hand | Scale rather than wear ends its useful life on hard water supply |

## How Many Spares per 1,000 Units

The ratios below are a starting point for a conversation, not a factory recommendation. They assume a low single digit warranty rate, a distributor who replaces parts rather than whole units, and a market where an end customer will fit a washer themselves. Adjust every line against your own return data as soon as you have any, because one season of real returns is worth more than any table.

Ask the factory for its own recommended ratios, and separately for the minimum order quantity that applies to spare parts, which is a different question from the product MOQ and is often the constraint that decides the order.

| Part | Illustrative quantity per 1,000 units | Basis |
| --- | --- | --- |
| O-ring set | 20 to 30 sets | Warranty replacements plus a service stock, at an assumed low single digit failure rate |
| Hose washer | 50 to 100 | The cheapest part in the box and the one most often lost during installation |
| Filter washer | 30 to 50 | Higher where the destination supply carries sediment |
| Cone nut | 10 to 20 | Cross threading is a user error rather than a product failure, and it is uncommon |
| Adapters | 30 to 50 of the type the market actually uses | Driven by the fitting mix in the destination, not by any failure rate |
| Complete hose | 10 to 20 | Transit damage and returns rather than in service failure |
| Replacement cartridge | One to two per unit per year of intended service | A sales forecast rather than a spares forecast, and the line where the recurring revenue sits |

## Writing Spares Into the Purchase Order

Spare parts get forgotten because they are cheap, and then they become urgent because they are unavailable. Six lines in the purchase order prevent the whole sequence.

1. List spare parts as their own SKUs with their own part numbers, rather than as a free allowance buried in the order.
2. Ask which parts are model specific and which are common across the range, because commonality is what decides how much service stock you actually need.
3. Specify the packaging for spares: bagged, boxed, or assembled into a service kit with a printed instruction sheet.
4. Agree the replacement cartridge programme at the same time as the head, since a filter product without a refill supply has a one year life.
5. Write the service life statement you intend to publish, with its condition attached, and check it against the evidence that actually exists.
6. Confirm the spare part minimum order quantity and lead time separately, because neither automatically follows the product MOQ.

## FAQ

### What O-ring sizes does a shower head use?

Sizes are model specific, because they follow the internal geometry of each body and mode switching structure rather than a standard. Ask for the size list against the models you are buying and specify the material with it. O-rings are 100% inspected at the supplier with AI camera vision.

### How often should a filter cartridge be replaced?

Depletion follows throughput rather than the calendar. Third party testing of the ACF media showed over 96.8% initial free chlorine removal and 90.6% after 5 tons of continuous flow, so an interval is best expressed in litres or tons, then translated into months for typical usage in your market.

### Are replacement cartridges supplied separately?

Yes. Refill cartridges are supplied as separate SKUs, which is what makes a filter shower head a repeat purchase rather than a one time sale. Agree the refill programme at the same time as the head, including packaging, part numbers and the replacement interval you intend to print.

### Should a check valve be included in the hose?

Only where a market rule or a buyer specification calls for it. A check valve prevents backflow into the supply and adds pressure loss, which is noticeable on a weak or gravity fed system. Name the requirement in the RFQ rather than adding the part as a general precaution.

### What happens if a customer removes the flow restrictor?

The product flows more and no longer matches the figure it was tested at, which can take it outside the flow limit that applies in its market. It is a common consumer modification, so state the tested flow with its pressure and avoid presenting a removable restrictor as a feature.

## Related pages

- Replacement filter cartridges: https://www.ningboware.com/shower-heads/replacement-shower-filter-cartridges/
- Filter media types and third-party data: https://www.ningboware.com/resources/shower-head-filter-media-types/
- https://www.ningboware.com/shower-heads/g1-2-shower-hoses/
- https://www.ningboware.com/resources/shower-head-adapters-fitment-by-market/
- https://www.ningboware.com/resources/shower-hose-and-thread-standards/
- All buyer guides: https://www.ningboware.com/resources/
- Send an RFQ: https://www.ningboware.com/contact/